Free Testking Pass4sure CCIE 350-001 Cisco 350-001 Download now from here.

You have a Catalyst 6500 with a Supervisor IA with a MSFC. After a power outage, the MSFC
has lost its boot image and now will only boot into ROMMON mode. You want to load a new
image onto the Catalyst MSFC boot flash. What method can you use?
A. Console connection using Xmodem
B. FTP
C. TFTP
D. SNMP
E. SSH
Answer: A
Explanation:
The Catalyst 6000 Supervisor I and II modules have an onboard Flash file system that can handle
several image files. In addition to this Flash, they also have a PCMCIA Flash slot. These
Supervisors run their software from RAM and do not need their Flash system once correctly
booted up. If an image is then corrupted or deleted, the standard upgrade procedure is always
possible as long as the Supervisor is running a valid image. If the Supervisor is not booting up
because there is no valid image to boot from the ROMMON, you will have to use the recovery
procedure.
Free cisco ccie 350-001 written exam free braindumps download now.
Which of the following statements regarding the use of SPAN on a Catalyst 6500 are true?
A. With SPAN an entire VLAN can be configured to be the source.
B. If the source port is configured as a trunk port, the traffic on the destination port will also be
tagged, irrespective of the configuration on the destination port.
C. In any active SPAN session, the destination port will not participate in Spanning Tree.
D. It is possible to configure SPAN to have a Gigabit port as the destination port.
E. In one SPAN session it is possible to monitor multiple ports that do not belong to the same
VLAN.
Answer: A, C, D, E
Explanation:
A destination port (also called a monitor port) is a switch port where SPAN sends packets for
analysis. If the trunking mode of a SPAN destination port is “on” or “nonegotiate” during SPAN
session configuration, the SPAN packets forwarded by the destination port have the ncapsulation
as specified by the trunk type; however, the destination port stops trunking, and the show trunk
command reflects the trunking status for the port prior to SPAN session configuration.
For a detailed discussion on SPAN and RSPAN refer the link below.

A new TACACS+ server is configured to provide authentication to a NAS for remote access
users. A user tries to connect to the network and fails. The NAS reports a FAIL message. What
could be the problem? (Choose all that apply).
A. The TACACS+ service is not running on the server.
B. The password for this user is incorrect.
C. The username does not exist in the TACACS+ user database.
D. The NAS server lost its route to the TACACS+ server.
E. The TACACS+ server is down.
Answer: B, C
Explanation:
A FAIL condition is a result of incorrect username/password information. It means that an
authentication request was successfully received, but that it had failed. A FAIL response is
significantly different from an ERROR. A FAIL means that the user has not met the criteria
contained in the applicable authentication database to be successfully authenticated.
Authentication ends with a FAIL response. An ERROR means that the security server has not
responded to an authentication query. Because of this, no authentication has been attempted.
Only when an ERROR is detected will AAA select the next authentication method defined in the
authentication method list.

You have forgotten the password to your Catalyst 5000 switch. Immediately after power cycling
the switch, you are faced with the password prompt. What default password should you type in?
A. cisco
B. abc123
C. sanfran
D. CTRL+ESC
E. No password, just hit the Enter key
Answer: E
Explanation:
Password recovery in Cat 5000 switch is performed in the following way. Power cycle the switch.
Hit the Enter key during the first 30 sec. The switch will allow you to get into the enable mode.
You will have 60 seconds to change the password and save the configuration change made
during this period.

While setting up remote access for your network, you type in the “aaa new-model” configuration
line in your Cisco router. Which authentication methods have you disabled as a result of this
change? (Choose all that apply.)
A. RADIUS
B. RADIUS+
C. Extended TACACS (XTACACS)
D. TACACS
E. TACACS+
F. Kerberos
Answer: C, D
Explanation:
When you enable AAA, you can no longer access the commands to configure the older
deprecated protocols, TACACS or Extended TACACS. If you decided to use TACACS or
Extended TACACS in your security solution, do not enable AAA.

Which of the following statement is true regarding clocking for a Cisco T1 interface?
A. The clock source command selects a source for the interface to clock received data.
By default, it is clock source loop-timed (specifies that the T1/E1 interface takes the clock from
the Tx (line) and uses it for Rx).
B. Routers are DTEs and NEVER supply clocking to T1/E1 line.
C. The clock source command specifies the location of the NTP server for timing.
D. The clock source selects a source for the interface to clock outgoing data.
The default is clock source line -Specifies that the T1/E1 link uses the recovered clock from
the line.
E. The clock source identifies the stratum level associated with the router T1/E1.
The default is Stratum 1.
Answer: D
Explanation:
Clocking can either be internal, looped, or line. The default is line, meaning that the router is
receiving clocking from the carrier network line.
Incorrect Answers:
C, E. These answers relate to NTP services, which are used for providing time stamping
information to the router and does not relate to clocking. Stratum levels provide a hierarchy to the
NTP source, with the highest level as 1.

Network management tools use Management Information Base (MIB) information to monitor and
manage networks. Which of the following is NOT part of the MIB-2 specification, as defined in
RFC 1213? (Choose all that apply)
A. The System Group
B. The TCP Group
C. The Transmission Group
D. The Enterprises Group
E. The RMON Group
F. The ICMP Group
Answer: D, E
Explanation:
RFC 1213 defines the “Management Information Base for Network Management of TCP/IP-based
internets: MIB-II” specification. It defines all of the following groups:
System, Interfaces, Address Translation, IP, ICMP, TCP, UDP, EGP, Transmission, and SNMP.
The RMON group is not part of RFC 1213, nor is the Enterprises Group

Which types of SNMPv1 messages are sent from the NMS (Network Management Station) using
SNMP version 1 to the Agent?
A. Trap, Get and Set
B. Get, Set and Getnext
C. Get, Set, Getnext and GetBulk
D. Get, Set and GetBulk
E. Trap only
Answer: B
Explanation:
SNMP itself is a simple request/response protocol, and the SNMPv1 operations used bythe NMS
are defined as below.
Get: Allows the NMS to retrieve an object variable from the agent. GetNext: Allows the NMS to
retrieve the next object variable from a table or list within an agent. In SNMPv1, when a NMS
wants to retrieve all elements of a table from an agent, it initiates a Get operation, followed by a
series of GetNext operations.
Set: Allows the NMS to set values for object variables within an agent.
Incorrect Answers:
A, E. SNMP traps are used by the agent to inform the NMS of some events.
C, D. GetBulk is used in SNMPv2, not version 1. SNMPv2 defines two new operations: GetBulk
and Inform. The GetBulk operation is used to efficiently retrieve large blocks of data. The Inform
operation allows one NMS to send trap information to another NMS and to then receive a
response. In SNMPv2, if the agent responding to GetBulk operations cannot provide values for all
the variables in a list, it provides partial results.